−Sidebar
hpl3:tools:materialeditor_mattype_soliddiffuse
−Table of Contents
Soliddiffuse material type
Texture Units
- Diffuse: base color data for the material.
- NMap: Normal Map, per-texel surface normal data. When enabled, the surface will get shaded according to the normal info.
- Specular: this unit will mask specular highlights.
- Alpha: this layer will mask any result using the alpha value (0 not visible - 1 fully visible)
- Height: this unit will store a map of height levels across the material. This unit is required to be enabled in order for Parallax Mapping to work.
- Illumination: the texture in this unit will be used as a self illumination pattern.
- CubeMap: this unit will make the material look as if reflecting an environment given by a cubemap texture.
- DissolveAlpha: this will be used for the dissolve effect.
- CubeMapAlpha: just like Alpha, but this unit will only mask the cubemap reflection.
- DetailDiffuse: this unit will be used as a detail texture for diffuse when enabled.
- DetailNMap: this unit will be used as a detail texture for the normal map when enabled.
- Translucency: texture that will mask light when seen through an object.
- Liquid: texture that will define the fading for the liquid effect.
Material specific variables
- HeightMapScale
- HeightMapBias
- IlluminationBrightness: Brightness of the illumination texture.
- FrenselBias: Bias for Fresnel term. values: 0-1. Higher means that more of reflection is seen when looking straight at object.
- FrenselPow: The higher the 'sharper' the reflection is, meaning that it is only clearly seen at sharp angles.
- AlphaDissolveFilter: If alpha values between 0 and 1 should be used and dissolve the texture. This can be useful for things like hair.
- DetailUvMul: The amount the UV maps are multiplied with. The higher the more the detail maps are repeated.
- DetailWeight(Diffuse,Specular,Normal): Weight for the detail for each texture. Valid values: 0 - 2.0
- DetailFadeStart: When the details start fading out.
- DetailFadeEnd: When details have completely faded out.
- SwayActive: If the model should sway according to wind properties. NOTE: Heightmap must be used to set the sway amount for each model part.
- SwayForceFieldAffected: If the model is affected by force fields.
- SwayFreq: The frequency of the sway movement.
- SwayAmplitude: How much the sway offsets the model at maximum (in meters).
- SwaySpeed: The speed of the sway.
- SwayOctaveMuls: The sway consists of the three (high - low) different freq movements, this is the factor for each.
- SwayForceFieldMul: Factor for the force field induced sway.
- SwayForceFieldMax: The max offset (after adding factor) can that be added from a force field.
- SwayYFreqMul: This can be used so that sway changes along the y-axis. The higher value the more change. 0=off (not used when SwaySingleDir is on)
- SwaySingleDir: If the sway should only be in a single direction.
- SwaySingleDirVector: If sway is only in a single direction, this is the direction!
- SwaySingleSampleVector: The direction of the sampling for the single dir sway.
- LiquidTrickleColor: The color and alpha of the liquid.
- LiquidTrickeSpecular: Specular color and power of the liquid (RGB, Power). If set to (0,0,0,0) the original specular map value will be used.
- LiquidTrickleLoopFade: If the liquid animation should loop and fade in again after it has faded out.
- LiquidTrickleFadeSpeed: How fast the liquid fades in and then stays before fading out again. Unit is in seconds (Fade In, Fade Out)
- LiquidTrickleEdgeSize: The size of the normal map edge generated by the trickling liquid.
- LiquidTrickleDryness: How long the generated liquid normal map should stay before drying back to the original normal map
- LiquidTrickleBlendMode: Which blend mode that should be used when combining the liquid with the color. Specular always uses Alpha.
hpl3/tools/materialeditor_mattype_soliddiffuse.1353670423.txt.gz · Last modified: 2012/11/23 11:33 by luis
